SupaScreen Security Screen Care and Maintenance

SupaScreen security screens are an innovative product that allows unobstructed views, with maximum strength and security. They are extremely hardwearing and corrosion resistant, but regular maintenance is required to sustain the original look of the product.

MAINTENANCE:
SupaScreen product inspections and cleaning should take place 6 monthly in an average domestic environment, every 3 months if located in the inner city and monthly in an industrial/coastal setting.

The locking devices incorporated in these products are complex mechanisms and regular maintenance includes the occasional lubrication of moving parts, with an aerosol based lubricant.

To lubricate door locks, hold the handles down and spray into the latch bolt cavity, then operate a few times to spread the lubricant around the moving parts. Door handle pivots and hinge pivot pins can be lubricated where they fit into the lock body. It is not recommended to spray directly into the key slots of lock cylinders or onto the key. However, applied sparingly, dry graphite powder is a suitable lubricant for lock cylinders

CLEANING: The stainless steel screen should be regularly cleaned to maintain an unobstructed view and airflow

FRAME: The care and maintenance of SupaScreen frames are outlined below by simply the following these important steps:

1. Carefully remove any loose surface deposits with a wet sponge by gently rubbing.
2. Clean by gently rubbing the surface with a soft brush (non-abrasive) and a dilute solution of a mild detergent, e.g., pH-neutral liquid hand or dishwashing detergent in warm water to remove dust, salt, and other deposits. For stubborn stains use only recommended solvents on the affected area, e.g., Isopropyl alcohol (IPA) or methylated spirits and rinse off with clean water. Do not use other aggressive solvents.
3. Anodised finishes with greasy deposits or hard to remove grime, should be cleaned with a soft cloth dipped in white spirit, turpentine or kerosene, then wiped with a dry rag.
4. Rinse the surfaces with clean fresh water after cleaning to remove all residues. A quick wipe-over with an absorbent cloth or chamois will prevent water marks from forming.

DO NOT allow excessive amounts of water to enter the main lock and any auxiliary locks.
DO NOT use solvents or harsh detergents on any of the SupaScreen frame, screen or components as this could damage the finish and increase the likelihood of corrosion.

POWDER COATED / ANODISED ALUMINIUM - CARE & MAINTENANCE

To comply with warranty requirements and to extend the effective life of anodised/powder-coated finishes, very simple maintenance and regular visual inspections should be scheduled and undertaken.

MAINTENANCE:
In general, anodised or powder-coated aluminium in urban areas should be cleaned every three months and every six months in rural areas. In industrial and marine environments (within 1km of the sea), monthly cold water washing as well as six monthly washes, with warm water & detergent, is necessary.

NOTE: It is universally recognised some sunscreens adversely affect powder-coated finishes and this should be avoided near the product in question.

CLEANING:
1 - Carefully remove any loose deposits with a wet sponge.
2 -Clean by gently rubbing the surface with a soft brush (non-abrasive) and a dilute solution of a mild detergent, e.g., pH-neutral liquid hand or dishwashing detergent in warm water to remove dust, salt, and other deposits. For stubborn stains use only recommended solvents on the affected area, e.g., Isopropyl alcohol (IPA) or methylated spirits and rinse off with clean water. Do not use other aggressive solvents.
3 - Anodised finishes with greasy deposits or hard to remove grime, should be cleaned with a soft cloth dipped in white spirit, turpentine or kerosene, then wiped with a dry rag.
4 - Rinse off with lots of clean fresh water. A quick wipe-over with an absorbent cloth or chamois will prevent water marks from forming.

DO remove obvious deposits as they occur.
DO NOT use abrasive steel wool, scrapers, scouring liquids or powders to remove paint splashes - these will damage your anodised/powder coating.
DO NOT use aggressive solvents, thinners, petrol etc.. on powder coating as these solvents will attack gloss levels and reduce its life expectancy.
DO NOT let any solvents used on anodised finishes come in contact with any rubber components as they can degrade them.
DO NOT expose your anodised/powder coatings to excessive heat, heaters or hot air guns - these may damage the coating.

DO NOT allow sunscreens to come into contact with powder coated services